Search:

Here is a link to an article by Dave Rat that covers some of the topics in this thread:

http://www.prosoundweb.com/article/when_hearing_starts_to_drift/P1/

Here are a couple of links that may be appropriate for this thread:

Howard Page article on excessive low end in system tuning
http://clairglobal.com/2011_news/2011/LowEnd.pdf

Frequency...

Here is a link to the waves latency chart.

http://www.wavesupport.net/content.aspx?id=2213

Tell us a little more about your set up to compare the input channel's hpf & lpf to your reference input.
At which point in the chain/routing are you making the comparison?


Plug ins can range...

I have upgraded to Lion 10.7.2 and Smaart 7.3.02 as well and it all seems to be working as it should.

Anyone know when the Smaart Remote app that uses the API built into Smaart to transmit the data directly from a Smaart measurement engine over wifi to the iPad will be released?
Is it in Beta...

Here is another relevant article.
http://www.prosoundweb.com/article/when_hearing_starts_to_drift/

Try using splashtop remote if you are running Smaart on a mac.
Less lag than vnc and works well.
Decent refresh rate as well.

http://www.splashtop.com/remote

Has anyone else experienced the spl calibration changing over the course of your event?
I was wondering if it is a function of Smaart not tracking or the external device we use for the pre amp?
I'm...

If I understand correctly a third party calibration file for Smaart should be in .Txt file format
and use certain items, but especially two columns separated by tabs:
Frequency, & Magnitude...

When a third party does your mic calibration file, what is the criteria that Rational is needing for these files?
On-axis or off-axis calibrations from 5 Hz to 25 kHz?
Are multiple measurements...

The one drawback to the Motu 8 Pre is portability as it is a rack mount item.
For fly dates I use my SoundDevices usb pre.

Kip,
I use the Motu 8 Pre without the recording/matrix software and it runs like a champ on my MBP.
I use the firewire out from my Motu running V7.2 and also use it for playback from the MBP out...

Thank Arthur,
I sent them an e-mail for information this afternoon.
Took V 7.2 for a spin this morning was nice to pin traces to panes
and really looking forward to correction curves.
Thanks...

Does anyone have any vendors that can do mic calibration files for Audix TM 1's that were purchased prior to Rational carrying them in the RA store?
I would love to be able to take advantage of the...

I'm currently running V7 with a motu 8 pre and 4 TM1's and 1 EW M30 and I've yet to find any of these units to mod. Your point is valid as I would still need to purchase phantom power supplies to the...

It is my understanding there is a mod to bypass the compander circuit while I think this to be the case I'm still in the evaluation period of this route. I own one Lectrco TM 400 and the thought of...

Looking for two 500/600 mhz Dual Sennheiser Mikroport EM 2003 to mod into my test measurment setup. Any leads from my audio friends out there would be helpful. Found a few in the 700mhz range but...

Supposing I have a four input system processor I might route things like this:
Input A = Mix L Console Output
Input B = Mix R Console Output
Input C = Aux Console Output (for Subs)
Input D =...

(I also recomend extreme caution when mixing outputs with different paths. Often times Aux outputs do not share the same phase response with main outputs. Mixing them back together could cause a...

So, what I do is route or mix my A and B Inputs (stereo console Output) to the approriate places:
Input A to Output 1, 2, 3 and 7 and 8
Input B to Output 4, 5, 6 and 7 and 8
Input C to Output 7...

When zero is zero and you have optimized the system within the constraints of sub on an aux for your client, Where does where does the correct phase or altered phase end up after being changed in the...

I was wondering about other peoples approaches to the request of subs on an aux. Does one put subs on an aux at the request of the person using them or for ones self so as not to put inputs into...

Could you elaborate a bit more on your process of using warble tones after doing your phase alignment of subs/lows

Does anyone have any advice for getting good usable low frequency data in a dome situation with long decay times?